Alaxala AX6300S series Manuál s instrukcemi

ALAXALA AX6300S Quick Start Guide AX63S-Q001-50X Reading and storing this manual: z Before you use the equipment, carefully read

Safety Information  If anything seems wrong, immediately turn off the power. z If smoke or an unusual smell is emanating from the Switch, or if l

Safety Information  Ensure that the capacity for incoming current to the distribution board is greater than the operating current of the circuit bre

Safety Information  Place an insulation cover over the 0 V and -48 V terminals of a DC power cable. z Place an insulation cover over the 0 V and -

Safety Information  Handle power cables carefully. z Do not place anything heavy on a power cable. Do not pull, bend, or process a cable. Doing s

Safety Information  When pressing a switch on a management and switching unit, do not use anything with a fragile tip, or anything that might become

Safety Information  Do not install the Switch in a dusty or humid location. z Do not install the Switch in a dusty or humid location. Doing so co

Safety Information  Do not obstruct the ventilation slots. z Do not obstruct the ventilation slots of the Switch. Doing so causes heat to accumula

Safety Information  Do not allow hair or objects near the ventilation slots. z Because a Switch is equipped with internal cooling fan units, do n

Safety Information  When removing a fan unit, do not place your hands near the fan if it is rotating. z Immediately after a fan unit is removed, t

Safety Information  Cleaning z Remove dust on and around the Switch regularly. In addition to causing the Switch to stop, accumulated dust could

Safety Information  Do not turn off the power of the Switch power while software is being updated (while the ppupdate command is being executed).

Safety Information  When replacing a fan unit with the Switch turned on, observe the time limit. z When replacing a fan unit with the Switch on, y

Safety Information  Install optional modules carefully. z Follow the procedure below when you install an optional module. Failure to do so could

Safety Information  Do not use a TV or a radio near a Switch. z Placing a Switch near a TV or a radio could affect both devices. If you hear nois

Safety Information  Disposing of a Switch z When disposing of a Switch, you should either follow local ordinances or regulations or contact your

Safety Information Safety-17

1. Preparation 1. Preparation uide is in that manual organization, and where the manuals can be viewed from. eries manuals This chapter describ

1. Preparation 1.1 Reading sequence of AX6300S series manuals This section describes the sequence for reading the AX6300S series manuals. This Quick

1. Preparation 1.2 Verifying supplied components Check the packing list supplied with the Switch to verify that all components and accessories have be

 Relevant products This guide applies to AX6304S and AX6308S model Switches.  Export restrictions If you export this product, please check all

1. Preparation 1.3 Preparing required items To set up a Switch, prepare the following in addition to the Switch, components, and accessories.  Opera

1. Preparation 5  200 V AC power cable When using the Switch in a 200 V AC environment, use only a power cable that meets ALAXALA specifications. F

1. Preparation 6

2. Installing Switch 2. Installing a Switch le, or interface cable, and other accessories to a Switch to turning on the power. This chapter descr

2. Installing Switch 2.1 Installing a Switch This section describes the installation of a Switch. 2.1.1 Installation procedure overview  AX6304S

2. Installing Switch  AX6304S (DC power supply unit installed) Figure 2-3 AX6304S (front) Figure 2-4 AX6304S (rear) 9

2. Installing Switch  AX6308S (AC power supply unit installed) Figure 2-5 AX6308S (front) Figure 2-6 AX6308S (rear) 10

2. Installing Switch  AX6308S (DC power supply unit installed) Figure 2-7 AX6308S (front) Figure 2-8 AX6308S (rear) 11

2. Installing Switch 2.1.2 Detailed installation procedure [Step 1] Connecting power cables  When using the Switch at 100 V AC Connect the supplied

2. Installing Switch  When using the Switch at 200 V AC (Using a 200 V AC power cable you have obtained) 1. Remove the bracket that prevents disco

2. Installing Switch [Step 2] Attaching a wrist strap Attach an antistatic wrist strap to the wrist strap terminal. NOTE The terminal for an antistati

2. Installing Switch [Step 6] Checking the LEDs When the STATUS LED on a management and switching unit turns green, the Switch has started. The progr

2. Installing Switch 16 2.2 Other operations  Installing and removing optional modules For details about installing or removing optional modules, s

3. Required Operations When Installing a Switch 3. Required Operations When Installing a Switch the time and the administrator mode password and addi

3. Required Operations When Installing a Switch 3.1 Overview of the command input modes The command line interface (CLI) for this Switch has three com

3. Required Operations When Installing a Switch  Configuration command mode If you enter the configure command in administrator mode, the Switch ent

3. Required Operations When Installing a Switch 3.2 Overview of initial setup operations An overview of the operations necessary when installing a Swi

3. Required Operations When Installing a Switch 3.3 Login When the Switch is turned on, the login prompt is displayed. After the login prompt, type t

3. Required Operations When Installing a Switch 3.4 Setting the administrator mode password Specify the password for administrator mode. NOTE We rec

3. Required Operations When Installing a Switch 3.5 Adding a user ID and deleting the operator user ID [Step 1] Creating a user ID and setting the lo

I Preface Thank you for choosing an ALAXALA AX6300S series Switch, a multi-layer Switch. This guide describes the procedures from unpacking to t

3. Required Operations When Installing a Switch 24 3.6 Setting the time Specify the time zone and the current time. The following example shows the pr

4. Miscellaneous Operations 4. Miscellaneous Operations itch, check the operating status, and troubleshoot any problem that might occur. ement and

4. Miscellaneous Operations 4.1 Operation management and configuration settings For details about operation management and configuration settings, se

4. Miscellaneous Operations 27 4.2 Troubleshooting See the following manual for corrective actions to problems (the number in the parentheses is the

Preface II

Contents Preface...

Contents ii

Safety Information Safety Information  Using AX6300S series Switches correctly and safely z This guide provides important information for ensurin